Specification Sheet: FP 110/019
10/100/1000 Ethernet Switched Fabric Board
(click to view Ruggedized Air-Cooled or Ruggedized Conduction-Cooled)
Ethernet Switched Fabric
- 22-port or 24-port 10/100/1000Mbps Ethernet Switched Fabric board:-
- for use with PICMG® 2.16 and VITA 31.1 Packet Switched Backplanes (PSB)
- for use with non-PICMG 2.16 CompactPCI backplanes when used with AD FP1/001 transition module
- high performance Ethernet Switched Fabric:-
- implemented by Marvell® Prestera® 98DX240 single-chip switch
- full line rate Layer 2 switching engine
- 8K MAC address cache with automatic learning and aging
- auto-negotiation on all ports:-
- 1000Mbps full-duplex
- 10/100Mbps full-duplex and half-duplex
- EEPROM storage for user configuration data
- Fabric Switch Configuration software:-
- see separate SW FSC/001 datasheet
- 10-port board available:-
- see separate FP 110/008-U datasheet
Backplane Interfaces
- compatible with CompactPCI® Packet Switched Backplane (PSB):-
- conforms to the relevant sections of PICMG 2.16 R1.0
- supports geographic address (GA) on J2
- compatible with ANSI/VITA 31.1-2003 Gigabit Ethernet on VME64x backplanes
- 19 PSB Ethernet ports for PSB node boards
- Ethernet port for linking with second fabric board:-
- enables redundant fabric board
- J1, J2, J3 and J5 connectors fitted as standard
Front Panel Interfaces
- option for Ethernet user ports:-
- 4 x RJ45 connectors @ 10/100/1000Mbps
- 2 x SFP LC optical connectors @ 1000Base-SX with multimode optical fiber
- speed and Link/Activity LEDs for all Ethernet ports
- 1 user LED
- reset switch (recessed)
System Management
- board health and status management:-
- conforms to PICMG® 2.9 R1.0 (System Management Specification)
- implements the IPMB0 interface on J1
- microcontroller-based Peripheral Management Controller
- EEPROM for Field Replaceable Unit (FRU) and Sensor Data Record (SDR) storage
- hot swap insertion and removal
Quality of Service (QoS)
- supports prioritized packet streams for management of voice, video and data
- 4 hardware priority queues per port
- fixed priority or weighted fair queuing
- QoS traffic classification, determined by:-
- port ID
- IEEE 802.1p multimedia traffic tags
- IPv6 Traffic Class
Electrical Specification
- +5V (+5%/-3%) @ 3.8A (typical, with 4 x RJ45 front panel connectors)
- +12V (+5%/-5%) @ 0.01A (maximum)
- +3.3V and -12V supplies are not required
Safety
- PCB (PWB) manufactured with flammability rating of 94V-0
Environmental Specification
- operating temperature:-
- 0°C to +55°C (N-Series)
- -25°C to +70°C (E-Series)
- -40°C to +85°C (K-Series)
- 5% to 95% Relative Humidity, non-condensing (operating):-
- K-Series includes humidity sealant
- -40°C to +85°C (storage)
- 5% to 95% Relative Humidity, non-condensing (storage)
- ruggedized air-cooled version planned (copper only):-
- see separate FP 110/019-RA datasheet
- ruggedized conduction-cooled version available (copper only):-
- see separate FP 110/019-RC datasheet
Mechanical Specification
- 6U form factor: 9.2 inches x 6.3 inches (233mm x 160mm)
- single slot: 0.8 inches (20.3mm)
- connectors: IEC 60917 and IEC-61076-4-101 (PICMG 2.0 R3.0 S2.2) for J1, J2, J3 and J5
- shock:
- 20g, 11ms, ˝ sine (operating);
- 30g, 11ms, ˝ sine (non-operating)
- vibration:
- 5Hz-2000Hz at 2g, 0.38mm peak displacement (operating);
- 5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)